Understanding Cellular network technology. I think this topic can be useful for the people who wants to know about Cellular network technology. and here are the articles :
A cellular network is a radio network made up of a number of radio cells (or just cells) each served by a fixed transmitter, known as a cell site or base station. These cells are used to cover different areas in order to provide radio coverage over a wider area than the area of one cell. Cellular networks are inherently asymmetric with a set of fixed main transceivers each serving a cell and a set of distributed (generally, but not always, mobile) transceivers which provide services to the network's users.
( photo courtesy : Wikipedia )
Cellular networks offer a number of advantages over alternative solutions:
- increased capacity
- reduced power usage
- better coverage
FDMA works by using varying frequencies for each neighbouring cell. By tuning to the frequency of a chosen cell the distributed stations can avoid the signal from other cells. The principle of CDMA is more complex, but achieves the same result; the distributed transceivers can select one cell and listen to it. Other available methods of multiplexing such as polarization division multiple access (PDMA) and time division multiple access (TDMA) cannot be used to separate signals from one cell to the next since the effects of both vary with position and this would make signal separation practically impossible. Time division multiple access, however, is used in combination with either FDMA or CDMA in a number of systems to give multiple channels within the coverage area of a single cell.
Practically every cellular system has some kind of broadcast mechanism. This can be used directly for distributing information to multiple mobiles, commonly, for example in mobile telephony systems, the most important use of broadcast information is to set up channels for one to one communication between the mobile transreceiver and the base station. This is called paging. The details of the process of paging vary somewhat from network to network, but normally we know a limited number of cells where the phone is located (this group of cells is called a Location Area in the GSM or UMTS system, or Routing Area if a data packet session is involved). Paging takes place by sending the broadcast message to all of those cells. Paging messages can be used for information transfer. This happens in pagers, in CDMA systems for sending SMS messages, and in the UMTS system where it allows for low downlink latency in packet-based connections.
The increased capacity in a cellular network, compared with a network with a single transmitter, comes from the fact that the same radio frequency can be reused in a different area for a completely different transmission. If there is a single plain transmitter, only one transmission can be used on any given frequency. Unfortunately, there is inevitably some level of interference from the signal from the other cells which use the same frequency. This means that, in a standard FDMA system, there must be at least a one cell gap between cells which reuse the same frequency. The frequency reuse factor is the rate at which the same frequency can be used in the network. It is 1/K (or K according to some books) where K is the number of cells which cannot use the same frequencies for transmission. Common values for the frequency reuse factor are 1/3, 1/4, 1/7, 1/9 and 1/12 (or 3, 4, 7, 9 and 12 depending on notation). Code division multiple access-based systems use a wider frequency band to achieve the same rate of transmission as FDMA, but this is compensated for by the ability to use a frequency reuse factor of 1, for example using a reuse pattern of 1/1. In other words, adjacent base station sites use the same frequencies, and the different base stations and users are separated by codes rather than frequencies. While N is shown as 1 in this example, that does not mean the CDMA cell has only one sector, but rather that the entire cell bandwidth is also available to each sector individually. Depending on the size of the city, a taxi system may not have any frequency-reuse in its own city, but certainly in other nearby cities, the same frequency can be used. In a big city, on the other hand, frequency-reuse could certainly be in use.
With CDMA, multiple CDMA handsets share a specific radio channel; the signals are separated by using a pseudonoise code (PN code) specific to each phone. As the user moves from one cell to another, the handset sets up radio links with multiple cell sites (or sectors of the same site) simultaneously. This is known as "soft handoff" because, unlike with traditional cellular technology, there is no one defined point where the phone switches to the new cell. Modern mobile phones use cells because radio frequencies are a limited, shared resource. Cell-sites and handsets change frequency under computer control and use low power transmitters so that a limited number of radio frequencies can be reused by many callers with less interference. Since almost all mobile phones use cellular technology, including GSM, CDMA, and AMPS (analog), the term "cell phone" is used interchangeably with "mobile phone"; however, an exception of mobile phones not using cellular technology is satellite phones. There are a number of different digital cellular technologies, including: Global System for Mobile Communications (GSM), General Packet Radio Service (GPRS), Code Division Multiple Access (CDMA), Evolution-Data Optimized (EV-DO), Enhanced Data Rates for GSM Evolution (EDGE), 3GSM, Digital Enhanced Cordless Telecommunications (DECT), Digital AMPS (IS-136/TDMA), and Integrated Digital Enhanced Network (iDEN).
(FDMA) and
Mobile phone
A mobile phone (also known as a wireless phone, cell phone, or cellular telephone) is a long-range, electronic device used for mobile voice or data communication over a network of specialized base stations known as cell sites. In addition to the standard voice function of a mobile phone, telephone, current mobile phones may support many additional services, and accessories, such as SMS for text messaging, email, packet switching for access to the Internet, gaming, Bluetooth, infrared, camera with video recorder and MMS for sending and receiving photos and video, MP3 player, radio and GPS. Most current mobile phones connect to a cellular network of base stations (cell sites), which is in turn interconnected to the public switched telephone network (PSTN) (the exception is satellite phones). Mobile phones send and receive radio signals with any number of cell site base stations fitted with microwave antennas. These sites are usually mounted on a tower, pole or building, located throughout populated areas, then connected to a cabled communication network and switching system. The phones have a low-power transceiver that transmits voice and data to the nearest cell sites, normally not more than 8 to 13 km (approximately 5 to 8 miles) away. When the mobile phone or data device is turned on, it registers with the mobile telephone exchange, or switch, with its unique identifiers, and can then be alerted by the mobile switch when there is an incoming telephone call. The handset constantly listens for the strongest signal being received from the surrounding base stations, and is able to switch seamlessly between sites. As the user moves around the network, the "handoffs" are performed to allow the device to switch sites without interrupting the call.
Hand phones: what is a hand phone?
A hand phone contains its own battery power source and relies on radio waves for "wireless" communication to the Telephone Service Provider. From the service provider your call is routed to its destination with the same or another service provider. Hand phones are usually more expensive than fixed line telephones. GSM hand phones usually offer more services, smaller size, and longer standby and talk times than other hand phones. GSM telephones (900) are more common in other countries and therefore easier to connect for service, or resell, than are the GSM 1800 telephones. There are also Dual Band phones that work on GSM or GSM 1800 systems. Before buying a hand phone you should decide which service provider you are going to use. Your telephone needs to be compatible with the provider that you use. In buying a hand phone you should look at its features, the size, the amount of battery stand-by and talk time, and the warranty provided by the seller. The following features are provided by most GSM telephone companies, some of the features are provided by other types of telephones as well:Memory for frequently called phone numbers stored in the telephone
Voice mail - for callers to leave messages when you are not available
Call waiting and call diverting to manage incoming calls
Caller identification shows the number of an incoming call and allows screening of calls
Alarm, calculator, exchange conversion and games
Voice recognition dialing
One-touch dialing
Data transmission via PC of fax, e-mail, or the Internet for GSM telephones
Changeable phone ring tones
Sources : Wikipedia
Wikipedia
www.bigpond.com.kh
0 Comments